« previous next »
Pages: [1]   Go Down

Author Topic: motor mounts  (Read 2225 times)

Offline wedge

  • Trade Count: (2)
  • Master 6x6'er
  • *****
  • Posts: 1640
  • Country: us
  • Karma: +0/-0
  • Run it like a Big Block !
Re: motor mounts
« Reply #7 on: May 15, 2018, 06:34:51 PM »
Puts a lot of Vibration in the machine.
Logged
3= Amphicat. 1= StarCraft. 1= Max 2= Attex  And Counting

Offline snaps10

  • Trade Count: (0)
  • 6x6'er
  • **
  • Posts: 85
  • Karma: +0/-0
Re: motor mounts
« Reply #6 on: May 15, 2018, 02:03:55 PM »
I’ve got mine hard mounted to a unistrut frame I built. Is it bad to hard mount these v-twins?
Logged

Offline garretttpe

  • Trade Count: (0)
  • Sr. 6x6'er
  • ****
  • Posts: 449
  • Country: us
  • Karma: +0/-0
Re: motor mounts
« Reply #5 on: April 21, 2018, 07:23:22 PM »
Picture of my mounts, this was a weird angle, the threads in the middle of the mount are long enough for the engine and 2 thick washers, my nut and 2 threads extruding the end of the nut..
Logged

Offline garretttpe

  • Trade Count: (0)
  • Sr. 6x6'er
  • ****
  • Posts: 449
  • Country: us
  • Karma: +0/-0
Re: motor mounts
« Reply #4 on: April 21, 2018, 11:31:31 AM »
MSafi65
Yes I re installed the front bumper

Whipper
I prob tossed them, the mounts I installed where the same bolt config as the originals just a larger diameter. Maybe I am over thinking it and all is fine, I will try to take a pic of them today and show you all.

 
Logged

Offline Msafi65

  • Trade Count: (0)
  • Full 6x6'er
  • ***
  • Posts: 117
  • Country: us
  • Karma: +0/-0
Re: motor mounts
« Reply #3 on: April 20, 2018, 11:19:41 PM »
Did you install the adjustable bumper at front left on top of the frame? It slows the mounts to flex but not move to far toward transmission to change belt geometry. I believe it’s still available. 
Logged

Offline whipperag

  • Trade Count: (1)
  • Sr. 6x6'er
  • ****
  • Posts: 337
  • Karma: +0/-0
Re: motor mounts
« Reply #2 on: April 20, 2018, 08:08:50 PM »
I would’nt use the UHMW, it’s to hard and would’nt flex at all.
I would just order the factory stock mounts:
That’s all I have in Bridget’s SS and they seem to be fine without any problems.
When you did the overhaul what did you do with the old stock ones?
New ones will just bolt right up.
 popcorn popcorn
 banana dance dance banana
Logged
Whipperag

Offline garretttpe

  • Trade Count: (0)
  • Sr. 6x6'er
  • ****
  • Posts: 449
  • Country: us
  • Karma: +0/-0
motor mounts
« Reply #1 on: April 20, 2018, 05:33:06 PM »
3 years ago when I overhauled my Max I use rubber engine mounts that were twice the diameter of the original ones, same thickness, they seem to flex more than I would like, or maybe the engine is supposed to. I am thinking about now using 6 blocks of UHWM (I have a bunch of blocks)to keep the engine from flexing. would this shake the machine to much? or should I just order the stock mounts?
Logged
Pages: [1]   Go Up
« previous next »